How To Clean Zebra Thermal Printer Head

Video: Zebra Tabletop and Print Engine Printhead Cleaning Procedure

Article ID: 00864341

Issue / Question

This procedure details methods used for

• Cleaning the printhead on a Zebra Tabletop or Pax printer

• Printhead maintenance and intendance

Applicable To

Zebra Tabletop and Print Engine printers

Resolution / Answer

Cleaning The Zebra Printhead

Inconsistent impress quality such as voids in the bar codes or graphics may bespeak a dirty Printhead. For optimum performance, the printhead should be cleaned regularly. Zebra Technologies Corporation recommends performing the cleaning process when installing a new Whorl of Ribbon or after three rolls of label stock.

Note: Y'all are non required to turn off the printer power for this procedure.   Remove all rings, watches, hanging necklaces, identification badges, or other jewelry that could bear upon the impress caput or get caught in the printer.  If you turn off the power, you volition lose all temporary settings, such as characterization formats, and y'all must reload them earlier yous resume press.
Click here for information on extending the life of your printhead.

Printhead Cleaning Procedure:

1. Open the Printhead by moving the Printhead Lever to the Open position.
ii. Remove the media and ribbon (if present).
3. Use a cleaning swab (99.7% isopropyl booze) and wipe the impress elements from end to end. (The print elements are the grayish/ black strip just behind the chrome strip on the underside of the Printhead.) Allow a few seconds for the solvent to evaporate.
4. Rotate the Platen Roller and clean thoroughly with a cleaning swab.
5. Brush or vacuum any accumulated paper lint and dust away from the Rollers
and the Media and Ribbon Sensors.
6. Reload ribbon and/ or media, close and latch the Printhead, restore power
(if necessary) and run the Intermission Fundamental self test to check print quality.
Click here for Pens and Kits information

Note: Silverline RFID printer printheads must but be cleaned using Save-A-Printhead Cleaning Moving-picture show shown beneath.

Helpful Information

Extending the life of your printhead Read More>>

Tough or hardened printhead buildup can be removed using "Save A Printhead" Cleaning Strips  Read More than>>
Part Numbers for Relieve-A-Printhead Cleaning Film Kits. Order kit number: For Printers with Print Widths:

• 46902  3.0" – iv.0"  (76 mm–102 mm)
• 44902  4.0" – 5.0" (102 mm - 127 mm)
• 48902  5.0" – 6.0" (127 mm - 152 mm)
• 38902  6.0" – 7.0" (152 mm - 178 mm)
• 22902  viii.0" – 9.0" (178 mm - 229 mm)

• 105SLPlus Industrial Printers
• 105SLPlus Industrial Printers
• 110PAX Print Engines (disc.)
• 110Xi4 Industrial Printer
• 140Xi4 Industrial Printer
• 170Xi4 Industrial Printer
• 220Xi4 Industrial Printer
• All Surface RFID Label Solution
• Industrial Printers
• Impress Engines
• R110Xi4 RFID Printer
• Eleven Series Industrial Printers
• ZE500 Print Engines
• ZE500 Impress Engines
• ZE500R RFID Print Engine
• ZE500R RFID Print Engine
• ZM400
• ZM600
• ZT200 Series Industrial Printers
• ZT210 Industrial Printer
• ZT220 Industrial Printer
• ZT230 Industrial Printer
• ZT400 Series Industrial Printers
• ZT400 Serial RFID Printers
• ZT410 Industrial Printer
• ZT410 RFID Industrial Printer
• ZT420 Industrial Printer
• ZT420 RFID Industrial Printer

Source: https://www.zebra.com/us/en/support-downloads/knowledge-articles/zebra-tabletop-and-print-engine-printhead-cleaning-procedure-with-video.html

Posted by: jarvisclinking.blogspot.com

Share this post